PX6 Dasaita BootLoop after installing the wrong update
source link: https://forum.xda-developers.com/t/px6-dasaita-bootloop-after-installing-the-wrong-update.4562487/#post-88259423
Go to the source link to view the article. You can view the picture content, updated content and better typesetting reading experience. If the link is broken, please click the button below to view the snapshot at that time.
PX6 Dasaita BootLoop after installing the wrong update
RafRag
Member
I was having issues with the bluetooth on my dasaita PX6 for my camry so I tried to install an update on it. little did I know that it was the wrong update. so It updated to android 11 and continues to be in a bootloop. No matter how long I press the RST button it will not load into recovery mode. I have tried what feels like to be countless methods but I am getting no result. please may someone help me.
Just use original software update provided from your seller
Reactions: RafRag
RafRag
Member
Just use original software update provided from your seller
I really wish I could but the problem is that the headunit is not booting at all its stuck in a loop and it will not go into recovery mode thank you though!
I really wish I could but the problem is that the headunit is not booting at all its stuck in a loop and it will not go into recovery mode thank you though!
Did you install an update or flashed ROM ?
RafRag
Member
Did you install an update or flashed ROM ?
I installed an update. I accidentally installed android 11 thinking it was android 10
(I presume you have any available)
RafRag
Member
Use one of the updates for Anroid 10 and with correct resolution
(I presume you have any available)
I understand this now thanks but the problem is that I cant boot it into recovery or even get into the actual system because it is stuck on bootloop. I am going to try flashing the system in the morning. thanks again!
Transfer offline update files to USB drive (unzip from file two files inside a zip file and put them only on USB) and next time system starts (USB must be attached to port) with car it will automatically start update procedure and finish.
After updating it must enter Android that is dependable on what update you will perform (right one).
RafRag
Member
You don't need to bootup to update device!
Transfer offline update files to USB drive (unzip from file two files inside a zip file and put them only on USB) and next time system starts (USB must be attached to port) with car it will automatically start update procedure and finish.
After updating it must enter Android that is dependable on what update you will perform (right one).
Ok thank you I will try this right now and tell you how it goes!
RafRag
Member
RafRag
Member
Did you try to tap with finger in the middle of screen while USB is on and unit starts, to trigger update ?
No I did not I will try this once the unit powers off
RafRag
Member
Did you try to tap with finger in the middle of screen while USB is on and unit starts, to trigger update ?
do I have to tap the screen before I turn on the unit or once the unit is turned on?
RafRag
Member
Post Android system information including MCU version
Im so sorry but where would I find that at? I currently cannot look into the system right now.
RafRag
Member
Attachments
- IMG_9552.mp4731.3 KB · Views: 0
do I have to tap the screen before I turn on the unit or once the unit is turned on?
start tapping as soon as you give contact or hear unit is booting up
If still no prevail, disconnect canbus box from the unit and start without it, then reconnect and see if corrects it self
RafRag
Member
start tapping as soon as you give contact or hear unit is booting up
If still no prevail, disconnect canbus box from the unit and start without it, then reconnect and see if corrects it self
I tried to tap it as it loads up and still no prevail I do not know how to disconnect the canbus box. is there any tutorial on how to do this?
I tried to tap it as it loads up and still no prevail I do not know how to disconnect the canbus box. is there any tutorial on how to do this?
You must detach canbus box from backside of device if you have cnbus at all, it is square box connected to wire harness.
Recommend
About Joyk
Aggregate valuable and interesting links.
Joyk means Joy of geeK